Universal-electronics URC-3021 Uživatelský manuál Strana 12
- Strana / 22
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
12
PROGRAMMING FAVORITE CHANNEL SCAN
In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels,
in any order, that will be immediately scanned when
FAV is pressed (see
Using Channel Scan on the previous page).
NOTE: Favorite channels can only be programmed for one mode.After programming, if FAV
is pressed while in another mode, the remote control will start scanning all channels instead
(if applicable to the selected device).
1. On the remote control,press CBL/SAT or TV once.
2. Press and hold
SET until the LED (red light) blinks twice,
then release
SET.
3. Enter
9 - 9 - 6.The LED will blink twice.
4. Use the keypad to enter a favorite channel number (e.g.,
031). Then press SET once.
NOTE: If the original remote control required pressing an Enter key
to change the channel, also press the ENTER key after the channel
number (e.g., 0 - 3 - 1 - ENTER). On some satellite receivers and cable
boxes, you may need to press the SELECT(OK) key instead of ENTER.
5. If desired,repeat step 4 for each channel to be stored, up
to a total of 10 channels.
NOTE: If you try entering more than 10 channels, the remote control
will automatically exit programming. To change your favorite chan-
nel list at this point, you will first need to delete the existing list by
performing the steps in “Clearing Custom Programming” on page 14.
Then, perform the instructions in this section once again.
6. To exit programming with less than 10 favorite channels
stored, press and hold SET until the LED blinks twice.
Otherwise, the remote control will automatically exit the
program after 10 channels have been stored.
CHANGING VOLUME LOCK
The One For All 3 Device Universal Remote Control is set at the factory for
independent volume control of each selected device. However, you may
change the Volume Lock setting to
Global Volume Lock so that a device’s vol-
ume will be locked to one mode (e.g., to control TV volume in all other
modes).After that, if desired, you can perform
Individual Volume Unlock on
a selected device to set its volume control for independent operation.
Locking Volume Control To One Mode
(Global Volume Lock)
1. Press and hold SET until the LED (red light) blinks twice,
then release SET.
continued on next page...
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 12
- TABLE OF CONTENTS 2
- INTRODUCTION 3
- FEATURES AND FUNCTIONS 4
- Key Charts 5
- Device Table 6
- INSTALLING BATTERIES 7
- PROGRAMMING DEVICE CONTROL 8
- SEARCHING FOR YOUR CODE 9
- CHECKING THE CODES 9
- Master Power Macro onto the 10
- (cont’d) 11
- RE-ASSIGNING DEVICE KEYS 11
- USING CHANNEL SCAN 11
- CHANGING VOLUME LOCK 12
- CHANGING VOLUME LOCK (cont’d) 13
- CLEARING CUSTOM PROGRAMMING 14
- TROUBLESHOOTING 15
- INSTRUCTIONS TO THE USER 15
- LIFETIME WARRANTY 16
- ADDITIONAL INFORMATION 17
- MANUFACTURER’S CODES 18
- Setup Codes For TV/VCR Combos 20
Související produkty a manuály pro Dálkové ovládání Universal-electronics URC-3021
(64 stránky)Samsung LE40M61BS manuály
Uživatelské manuály a uživatelské příručky pro Televizory a monitory Samsung LE40M61BS.
Poskytujeme 1 manuály pdf Samsung LE40M61BS ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentáře k této Příručce